Articles
The Fastback 25 photobook binder is aneasy to use machine that is designed to be used as part of the PowisPhotobook Workcell. However, even easy to use machines can haveproblems from time to time. This article will give you some basicinstructions for troubleshooting problems with your Fastback 25. Itwill teach you how to open the machine, remove a jammed strip and cleanyour machine.
Opening The Fastback 25
If you ever need to work or clean inside the Fastback Photobook Model 25 binder, you must open the cover. Here is how...
1.Switch the power off.
2. For North American models you simply reach under the cover, and pullthe release catch forward until the top cover pops up slightly. Gentlypush the cover backward until it stops in the upright position. Itworks just like the hood of a car. If you have a European model of theFastback 25 you will need to use the key that is provided to open thecover of the machine.
Removing Jammed Strips
1.Open the binder cover.
2.Directly in front of the heating platen is the black metal book rest; flip this up.
3. Now inspect the bottom of the binder. The strip will probably befound here. If it isn't, it is most likely in the feed slot or stuck tothe platen.
4.Using the tongs provided with your Fastback binder, remove the strip from the binder.
5.If there is any glue on the platen, this is a good time to clean it.
6.Close the cover.
Recommended Maintenance - Cleaning the Platen
If a Fastback strip gets stuck in the machine or melted to the platen,or if adhesive has spilled out onto the heater plate, you'll need toclean your machine to ensure proper operation. If can wait for about anhour for your ultrasonic fabric sewing machine factory Fastback to completely cool, you should clean the platenwhen it is cold. If the heater plate and components in your machine arecompletely cool, the adhesive should wipe off using a cotton clothdampened in a citrus cleaning solution such as Fastback Icky StickyStuff Remover. However, if you notice adhesive is causing you problemsand you can't wait for the machine to cool, you can clean the machinehot. Here is how...
1. First put on the oven mitt (heat protective glove) that came withyour machine. It is important to always wear this glove when workingwith a Fastback machine that hasn't had adequate time to cool. Theplaten and back-up bars can be very hot.
2. Next, using the instructions above, open the cover of your Fastbackmachine to its full upright position. Once the machine is open you willsee the Teflon-coated platen that runs across the center of themachine.
3. Once you have located the heater plate, you will need to flip up thebook rest to access the top of the platen. Now you can wipe off anyglue with a clean dry cloth. DO NOT use Icky Sticky Stuff Remover orcitrus solution on the hot platen. These solutions should only be usedwith the machine is cold.
4. Wipe off any adhesive on both back-up bars or any of the clampingsurfaces inside the machine. If the unit has cooled, wipe off any gluewith a cotton cloth dampened in the Citrus cleaning solution. You canalso peel the adhesive off the upper side of the platen with yourfingers (or a wooden instrument, like a popsicle stick).
https://www.fycgultrasonic.com/
Opening The Fastback 25
If you ever need to work or clean inside the Fastback Photobook Model 25 binder, you must open the cover. Here is how...
1.Switch the power off.
2. For North American models you simply reach under the cover, and pullthe release catch forward until the top cover pops up slightly. Gentlypush the cover backward until it stops in the upright position. Itworks just like the hood of a car. If you have a European model of theFastback 25 you will need to use the key that is provided to open thecover of the machine.
Removing Jammed Strips
1.Open the binder cover.
2.Directly in front of the heating platen is the black metal book rest; flip this up.
3. Now inspect the bottom of the binder. The strip will probably befound here. If it isn't, it is most likely in the feed slot or stuck tothe platen.
4.Using the tongs provided with your Fastback binder, remove the strip from the binder.
5.If there is any glue on the platen, this is a good time to clean it.
6.Close the cover.
Recommended Maintenance - Cleaning the Platen
If a Fastback strip gets stuck in the machine or melted to the platen,or if adhesive has spilled out onto the heater plate, you'll need toclean your machine to ensure proper operation. If can wait for about anhour for your ultrasonic fabric sewing machine factory Fastback to completely cool, you should clean the platenwhen it is cold. If the heater plate and components in your machine arecompletely cool, the adhesive should wipe off using a cotton clothdampened in a citrus cleaning solution such as Fastback Icky StickyStuff Remover. However, if you notice adhesive is causing you problemsand you can't wait for the machine to cool, you can clean the machinehot. Here is how...
1. First put on the oven mitt (heat protective glove) that came withyour machine. It is important to always wear this glove when workingwith a Fastback machine that hasn't had adequate time to cool. Theplaten and back-up bars can be very hot.
2. Next, using the instructions above, open the cover of your Fastbackmachine to its full upright position. Once the machine is open you willsee the Teflon-coated platen that runs across the center of themachine.
3. Once you have located the heater plate, you will need to flip up thebook rest to access the top of the platen. Now you can wipe off anyglue with a clean dry cloth. DO NOT use Icky Sticky Stuff Remover orcitrus solution on the hot platen. These solutions should only be usedwith the machine is cold.
4. Wipe off any adhesive on both back-up bars or any of the clampingsurfaces inside the machine. If the unit has cooled, wipe off any gluewith a cotton cloth dampened in the Citrus cleaning solution. You canalso peel the adhesive off the upper side of the platen with yourfingers (or a wooden instrument, like a popsicle stick).
https://www.fycgultrasonic.com/
Posté le 25/03/2021 à 02:40 par efficient
Catégorie mi cable manufacturers
0 commentaire : Ajouter
Batters should always wear the necessary protectivegear when in the cage with a machine or on the fieldfor grounders or fly balls. Helmets and protectivecups are a must. Do not allow any player into the cageif they are not wearing an officially sanctionedbatting helmet.
The person feeding a pitching machine should alwaysstand behind an L-screen or similar barrier and shouldwear a helmet themselves as a precaution againstbatted balls hitting the ceiling of the cage andfalling down.
If using a pitching machine after rain, or on a dewymorning, balls will pick up the moisture and canbehave unpredictably on feeding through the pitchingmachine. Make sure your hitters are extra vigilant asa pitched ball may come out of the machineerratically.
Visually inspect batting cage and L-screen nettingregularly and patch when necessary. A hole in thenetting can quickly lead to accidents. As a part ofthis, always use high quality, thick netting material.In the long run, this will prove safer and more costeffective than using cheap material in the beginning.
In the batting cage, only two people should bepresent at any given time The batter and the feederbehind their screen.
Use good judgment in setting the pitching machinesspeed to a players ability. Just because a pitchingmachine can throw a ball at 102 MPH doesnt mean yourplayer is ready for that speed.
Before any batter enters the cage, always feed a fewtest pitches into the pitching machine to ensure thatthe pitching machine is accurately aimed and so thatthe batter has an idea of what to expect. Perform thesame procedure when any adjustment is made to themachine, i.e. a new type of pitch or a differentspeed.
When setting up the pitching machine, make sure themachine is level and the legs properly stabilized.
Any power cords running to the machine should befirmly plugged in and should be regularly examined forfraying.
Damaged, sliced, or cracked balls may behaveerratically and should be replaced as soon aspossible.
The person feeding the pitching machine shouldalways let the batter know to expect a pitch.Generally this is done by holding the ball up overyour head and then placing it in the feeder.
Regularly check your pitching machine for wheeldamage or other problems that may impact its abilityto perform properly.
Never operate a pitching machine under the influenceof drugs or alcohol. This is by no means an exhaustive list, but simply some of the important safety tips we have collected in our many years of using pitching machines safely, effectively, and enjoyably. A pitching machine is a tremendous tool for improving your baseball skills, but like any machine, it can be dangerous if not used properly and with care. So get out there and enjoy all the benefits of your new Jugs or Atec machine, but remember that safety always come first. For the final word on any safety or maintenance issue Ultrasonic Welding Transducer relating to your pitching machine, please consult the manual that came with it.
Disclaimer: Under no circumstances shall the operator of this website, or its officers, agents, employees, or counsel be liable to any person or entity for any loss or damage in whole or part caused by, resulting from, or relating to any error or omission (through neglect or otherwise) or other circumstances involving the procurement, collection, compilation, interpretation, analysis, editing, transportation, transmittal, communication or delivery of any information contained in this website.
https://www.fycgultrasonic.com/
The person feeding a pitching machine should alwaysstand behind an L-screen or similar barrier and shouldwear a helmet themselves as a precaution againstbatted balls hitting the ceiling of the cage andfalling down.
If using a pitching machine after rain, or on a dewymorning, balls will pick up the moisture and canbehave unpredictably on feeding through the pitchingmachine. Make sure your hitters are extra vigilant asa pitched ball may come out of the machineerratically.
Visually inspect batting cage and L-screen nettingregularly and patch when necessary. A hole in thenetting can quickly lead to accidents. As a part ofthis, always use high quality, thick netting material.In the long run, this will prove safer and more costeffective than using cheap material in the beginning.
In the batting cage, only two people should bepresent at any given time The batter and the feederbehind their screen.
Use good judgment in setting the pitching machinesspeed to a players ability. Just because a pitchingmachine can throw a ball at 102 MPH doesnt mean yourplayer is ready for that speed.
Before any batter enters the cage, always feed a fewtest pitches into the pitching machine to ensure thatthe pitching machine is accurately aimed and so thatthe batter has an idea of what to expect. Perform thesame procedure when any adjustment is made to themachine, i.e. a new type of pitch or a differentspeed.
When setting up the pitching machine, make sure themachine is level and the legs properly stabilized.
Any power cords running to the machine should befirmly plugged in and should be regularly examined forfraying.
Damaged, sliced, or cracked balls may behaveerratically and should be replaced as soon aspossible.
The person feeding the pitching machine shouldalways let the batter know to expect a pitch.Generally this is done by holding the ball up overyour head and then placing it in the feeder.
Regularly check your pitching machine for wheeldamage or other problems that may impact its abilityto perform properly.
Never operate a pitching machine under the influenceof drugs or alcohol. This is by no means an exhaustive list, but simply some of the important safety tips we have collected in our many years of using pitching machines safely, effectively, and enjoyably. A pitching machine is a tremendous tool for improving your baseball skills, but like any machine, it can be dangerous if not used properly and with care. So get out there and enjoy all the benefits of your new Jugs or Atec machine, but remember that safety always come first. For the final word on any safety or maintenance issue Ultrasonic Welding Transducer relating to your pitching machine, please consult the manual that came with it.
Disclaimer: Under no circumstances shall the operator of this website, or its officers, agents, employees, or counsel be liable to any person or entity for any loss or damage in whole or part caused by, resulting from, or relating to any error or omission (through neglect or otherwise) or other circumstances involving the procurement, collection, compilation, interpretation, analysis, editing, transportation, transmittal, communication or delivery of any information contained in this website.
https://www.fycgultrasonic.com/
0 commentaire : Ajouter
The Tamerica Tashin 210EPB is a heavy duty all metal electric plasticcomb binding machine. This effective machine makes punching documentsis as easy as pressing a button. It's the binding solution that manycompanies need to bind efficiently with plastic comb technology. Thisis the electric plastic comb binder you have been waiting for - and itwill change the way you approach a plastic binding application. TheTamerica Tashin 210EPB is worth your consideration and should be lookedat carefully before making any decision regarding the right bindingmachine for you.
Features:
There are many features that are perfect for high-volume users. Forexample, the 210EPB is capable of punching up to 10,000 sheets per houror approximately 20 sheets per lift - ideal for users who bindhigher-volume documents, and need to use this application on a regularbasis - every day. In addition, the 210EPB Includes a depth of punchmargin adjustment for binding both thin and thick documents and fullydisengageable dies with an open-throat design for binding short andlong documents. The punch will handle up to 12" documents in a singlepass and longer documents in two passes, making it highly efficient.This versatile machine runs the gamut of sizes and thicknesses and canbind documents as thin as just a few sheets with 3/16" combs or asthick as 425 sheets with 2" combs. In addition, the heavy-duty handlethat controls the plastic comb opener, can be repositioned allowing foropening combs longer than 12."
Limitations:
As helpful as the 210EPB can be, it does have some limitations,including a fairly long punch cycle, adding to the time it takes fromthe push of the button until the punch is complete. This time lag isnot a problem for all applications, for instance, the moderate volumeusers for this equipment do not find the time lag an issue. However,for higher-volume users, the slower punch cycle can be problematic.
In addition, this machine does not have a foot pedal activation switchfor punching. The foot pedal activation can be quite useful for anelectric machine, because it allows you to hold the documents with bothhands, making it possible to guide the documents through the system.
Construction:
The 210EPB is made of heavy-duty steel . This type of constructionmakes the 210EPB a product that is build to last. The 210EPB can holdup well in large-volume applications, but works fine with small tomoderate applications. The machine's large chip tray is made ofhardened plastic and the whole unit comes with a 1 year warranty. Thatbeing said, the warranty may never be necessary, given the solid steelconstruction of the machine - There is rarely a need to use thewarranty offered. This does serve to prove, however, just howwell-constructed the 210EPB really is .
Recommendation:
The 210EPB is a useful, well-built machine at a good value. The machinehas all of the important features you look for in a high-qualityelectric comb China cavitation machine suppliers binding machine. From the machine's solid construction,to the functional features of the 210EPB, this machine ishighly-recommended for medium sized offices that do moderate volumebinding. Larger organizations, however, may want to opt for a machinewith a foot pedal and a faster punching cycle. No matter what thechoice, however, the 210EPB should be considered for companies withmoderate binding needs.
https://www.fycgultrasonic.com/
Features:
There are many features that are perfect for high-volume users. Forexample, the 210EPB is capable of punching up to 10,000 sheets per houror approximately 20 sheets per lift - ideal for users who bindhigher-volume documents, and need to use this application on a regularbasis - every day. In addition, the 210EPB Includes a depth of punchmargin adjustment for binding both thin and thick documents and fullydisengageable dies with an open-throat design for binding short andlong documents. The punch will handle up to 12" documents in a singlepass and longer documents in two passes, making it highly efficient.This versatile machine runs the gamut of sizes and thicknesses and canbind documents as thin as just a few sheets with 3/16" combs or asthick as 425 sheets with 2" combs. In addition, the heavy-duty handlethat controls the plastic comb opener, can be repositioned allowing foropening combs longer than 12."
Limitations:
As helpful as the 210EPB can be, it does have some limitations,including a fairly long punch cycle, adding to the time it takes fromthe push of the button until the punch is complete. This time lag isnot a problem for all applications, for instance, the moderate volumeusers for this equipment do not find the time lag an issue. However,for higher-volume users, the slower punch cycle can be problematic.
In addition, this machine does not have a foot pedal activation switchfor punching. The foot pedal activation can be quite useful for anelectric machine, because it allows you to hold the documents with bothhands, making it possible to guide the documents through the system.
Construction:
The 210EPB is made of heavy-duty steel . This type of constructionmakes the 210EPB a product that is build to last. The 210EPB can holdup well in large-volume applications, but works fine with small tomoderate applications. The machine's large chip tray is made ofhardened plastic and the whole unit comes with a 1 year warranty. Thatbeing said, the warranty may never be necessary, given the solid steelconstruction of the machine - There is rarely a need to use thewarranty offered. This does serve to prove, however, just howwell-constructed the 210EPB really is .
Recommendation:
The 210EPB is a useful, well-built machine at a good value. The machinehas all of the important features you look for in a high-qualityelectric comb China cavitation machine suppliers binding machine. From the machine's solid construction,to the functional features of the 210EPB, this machine ishighly-recommended for medium sized offices that do moderate volumebinding. Larger organizations, however, may want to opt for a machinewith a foot pedal and a faster punching cycle. No matter what thechoice, however, the 210EPB should be considered for companies withmoderate binding needs.
https://www.fycgultrasonic.com/
0 commentaire : Ajouter